The task of the check control is to inform the driver. It provides him with information via the text display in the display unit of the IKE (E38/E39 high) or via the LC display field for check control messages in the instrument cluster (E39 basic) regarding failure of important functions as well as notes and warnings.
The check control function in the LCM monitors its own sensors and detects when a message is necessary for these sensors. Consequently it sends a data telegram to the IKE/instrument cluster with the request to display the message text in the text display or the message in the display field for check control messages.
The following sensors are monitored:
The LCM is additionally connected via a line to the EML and DDE control units.
An ignition lock and belt buckle contact is included in the US version.
In addition, it also receives LCM-internal messages concerning defective lamps.
Added to this, it evaluates messages from other control units which it receives via the I-bus and sends the corresponding request to the IKE/instrument cluster.
The messages are, in part, accompanied by an acoustic annunciator.
The gong in conjunction with check control messages is activated via the I-bus (no direct line link between the LCM and gong). It should be noted that depending on the importance and number of messages previously occurred an acoustic signal does not sound every time and also not for the same message.
The following check control text messages are possible in the E38/E39 high system:
Check engine oil level
The level is determined by a thermal oil level sensor.
It supplies a square-wave signal and receives voltage as of terminal 15.
Check brake fluid
Top up wash water
Check coolant level
Engine emergency program
If problems are detected at the throttle or at the pedal sensor, the EML assumes emergency mode, accompanied by a distinct reduction in engine performance. In this case, the check control receives a signal via a line, with which the LCM is connected directly to the EML, and outputs this message.
Preheating/injection systemg
The LCM is connected via a line to the DDE control unit, from which it receives a signal for the messages preheating and injection system.
EEPROM LCM
appears when the LCM is not coded.
Ignition key in lock (US only)
A switch connected to ground is located in the ignition lock. The display is shown when the driver's door is open until the ignition key is removed, however, only at "ignition OFF".
Buckle belt (US, Gulf States only)
The message appears when the seat belt has not been buckled (closed). The belt contact switch which switches to ground is connected directly to the LCM.
Information which the check control receives from the IKE/instrument cluster:
The check control receives information from the IKE for the following messages. Troubleshooting should be continued in the IKE if incorrect messages are received.
Transmission emergency program
If there is a defect in a transmission control unit to the IKE, the LCM is informed via the I-bus.
Release parking brake
This message appears on exceeding a speed of 5 km/h with the parking brake applied.
Check brake pad
Coolant temperature
Stop! Engine oil pressure
Information which the check control receives from the ZKE:
The check control receives information from the ZKE and processes it for the following messages. Troubleshooting should be continued in the ZKE if incorrect messages are received.
Door open
This message is output as of a speed of 5 km/h if the driver's, passenger's or rear door is open.
Luggage compartment (boot/trunk) open
This message appears on exceeding a speed of 5 km/h with the boot/trunk lid open.
Light on?
This indication appears in ignition lock position "0" when the driver's door is opened with the parking light switched on.
The LCM evaluates all light messages internally.
On vehicles with the basic system, information is indicated not in the form of text messages but rather by warning lamps and symbols in the LC display field for check control messages in the instrument cluster.
The check control also requests indication for following lamps:
General brake warning lamp
This switch is activated by the LCM when its brake fluid level switch informs it that the brake fluid level is too low.
Wash water
This lamp lights when the switch connected to the LCM signals that the wash water level is too low.
Oil level indicator lamp
The oil level is determined by a thermal oil level sensor. It is connected directly to the LCM and supplies a square-wave signal with a frequency serving as a measure for the level. It receives its power supply as of terminal 15.
Preheating
The LCM is connected via a line link to the DDE control unit, from which it receives the signal to activate this lamp.
Seat belt indicator lamp
On US and Gulf State vehicles, this lamp lights as of "ignition ON" when the seat belt has not been buckled (closed). The belt contact switch which switches to ground is connected directly to the LCM.
Defective lamps (in the LC display for check control messages)
Door messages (in the LC display for check control messages)
Catalytic converter overheating (Japan version only)
Additionally: Gong with ignition key in lock (US version only)